一、工作服衬衫外观检验

　　1、 Appearance inspection of work clothes and shirts

　　粗纱、走纱、飞纱、暗横、白迹、破损、色差、污渍。

　　Roving, running yarn, flying yarn, dark horizontal, white marks, damage, color difference, stains.

　　二、尺寸检验

　　2、 Dimensional inspection

　　严格按照尺寸表。

　　Strictly follow the size chart.

　　工作服衬衫定制

　　Customized workwear and shirt

　　CUSTOMISATION

　　Customization

　　如需采购定制工作服请直接联系哥登服饰客服人员：18113135882（同V）

　　If you need to purchase customized work clothes, please contact the customer service staff of Gordon Clothing directly: 18113135882 (same as V)

　　厂家直供，保证质量！

　　Directly supplied by the manufacturer, ensuring quality!

　　三、对称检验

　　3、 Symmetry test

　　1、领尖大小、领骨是否相对；

　　1. Is the size of the collar tip and whether the collar bone is relative;

　　2、两膊、两夹圈的阔度；

　　2. The width of the two arms and two clips;

　　3、两袖长短、袖口宽窄、袖褶距离、袖叉长短、介英高度；

　　3. Two sleeve length, cuff width, sleeve fold distance, sleeve fork length, and sleeve height;

　　4、担干两边高度；

　　4. Shoulder the height on both sides;

　　5、口袋大小、高低；

　　5. Pocket size and height;

　　6、门襟长短，左右条格对称。

　　6. The length of the front placket is symmetrical with the left and right stripes.

　　四、做工检验

　　4、 Workmanship inspection

　　1、各部位线路顺直松紧适宜，不可有浮线、跳线、断线现象，驳线不可太多且不能出现在显眼位置，针距不能过疏过密，依照规程；

　　1. The wires in each part should be straight and have appropriate tightness, without floating wires, jumpers, or broken wires. There should not be too many connecting wires and they should not appear in prominent positions. The needle spacing should not be too loose or too dense, in accordance with regulations;

　　2、领尖要贴服，领面不可鼓起，领尖无断尖，止口无反吐。领窝留意底线与否外露，止口要整齐，领面松紧适宜不反翘，领底不可外露；

　　2. The collar tip should be snug, the collar surface should not bulge, the collar tip should not be broken, and there should be no regurgitation at the mouth. Pay attention to whether the bottom line of the collar is exposed, the seam should be neat, the tightness of the collar surface should be appropriate without warping, and the collar bottom should not be exposed;

　　3、门襟要直，平服，侧缝顺直，松紧适宜，宽窄一致；

　　3. The front placket should be straight, flat, with straight side seams, suitable elasticity, and consistent width;

　　4、明袋内止口要清剪，袋口平直，袋角圆顺，封口大小一致，牢固；

　　4. The inner edge of the bag should be cut clean, the bag opening should be straight, the bag corners should be round and smooth, the sealing size should be consistent, and it should be firm;

　　5、衫摆不可扭边外翘，直角摆要顺直，圆底摆角度一致；

　　5. The hem of the shirt should not be twisted or curled outward. The right angle hem should be straight, and the angle of the round bottom hem should be consistent;

　　6、面线与底线的松紧要适当,避免起皱(易起皱的部位有领边、门襟、夹圈、袖底、侧骨、袖叉等)；

　　6. The elasticity of the top and bottom lines should be appropriate to avoid wrinkling (areas prone to wrinkling include collar edges, placket, clip rings, sleeve soles, side bones, sleeve forks, etc.);

　　7、上领、埋夹收拾要均匀，避免容位太多（主要部位是：领窝、袖口、夹圈等）；

　　7. The upper collar and buried clip should be cleaned evenly to avoid too many spaces (the main parts are: collar, cuffs, clip rings, etc.);

　　8、钮门定位要准，开刀利落无线毛，大小应与纽扣相匹配，钉钮位要准（尤其是领尖），钮线不可过松过长；

　　8. The positioning of the button door should be accurate, the incision should be sharp and free of burrs, the size should match the button, the nail button position should be precise (especially the collar tip), and the button thread should not be too loose or too long;

　　9、打枣粗幼、长短及位置要符合要求；

　　9. The thickness, length, and position of jujube should meet the requirements;

　　10、对条、对格主要部位：左右幅与门襟相对，袋片与衫片相对，前后幅对，左右领尖、袖片、袖叉对；

　　10. The main parts of the stripes and grids are: the left and right panels are opposite to the placket, the pocket panels are opposite to the shirt panels, the front and back panels are opposite, and the left and right collar tips, sleeve panels, and sleeve forks are opposite;

　　11、顺逆毛面全件顺向一致。

　　11. The whole piece of the rough surface is consistent in the forward and reverse directions.

　　五、整烫检验

　　5、 Ironing inspection

　　1、位整烫平服，无烫黄、机关、水渍、脏污等；

　　1. The garment is fully ironed and flat, without yellowing, mechanical damage, water stains, dirt, etc;

　　2、整烫重要部位：领、袖、门襟；

　　2. Important areas for ironing: collar, sleeves, and placket;

　　3、线头要彻底；

　　3. The thread ends should be thoroughly removed;

　　4、注意朴渗透胶。

　　4. Pay attention to the penetration adhesive.

　　六、物料检查

　　6、 Material inspection

　　唛头位置及车缝效果，挂牌是否正确，有无遗漏，胶袋质地、落朴效果，所有物料必须依照物料单指示。

　　The position and stitching effect of the marking, whether the hanging is correct, whether there are any omissions, the texture of the plastic bag, and the effect of falling, all materials must be in accordance with the instructions on the material list.

　　七、包装检查

　　7、 Packaging inspection

　　严格按照包装指示。

　　Strictly follow the packaging instructions.

　　八、出口衬衫检验方法

　　8、 Inspection method for export shirts

　　1.制作

　　1. Production

　　衬衫的工业生产，采用的流水工艺，在一条生产流水线上有各种不同的生产设备和操作的技术工人，整个制造流程包括款式、规格及生产工艺的设计，在工艺设计方面采用“立体造型，平面裁剪”增加缝、接开刀、收省、打褶等技术，同时又包括验料、排料划皮、缝制和熨烫整型等多种生产工艺。

　　The industrial production of shirts adopts the best flow process, with various production equipment and skilled workers operating on a single production line. The entire manufacturing process includes the design of styles, specifications, and production processes. In terms of process design, "three-dimensional modeling, flat cutting" is used to increase sewing, cutting, saving, pleating, and other technologies. At the same time, it also includes multiple production processes such as material inspection, cutting, sewing, and ironing shaping.

　　3.产地及输出国别

　　3. Origin and country of export

　　(1)、衬衫的生产遍及全国各省、市和乡村，其生产量和销售量均比其它服装数量大，市场广阔。

　　(1) The production of shirts covers all provinces, cities, and rural areas in China, with a larger production and sales volume than other clothing products, and a broad market.

　　(2)、衬衫输往已发展到五大洲100多个和地区。

　　(2) Shirt exports have developed to over 100 countries and regions across five continents.

　　4.种类

　　4. Types

　　衬衫主要包括有各种面料制成的高、中、低档，男、女、童的长袖、短袖、硬领、无领、无袖和绣花等衬衫。

　　Shirts mainly include high, medium, and low-end shirts made of various fabrics, including long sleeved, short sleeved, hard necked, collarless, sleeveless, and embroidered shirts for men, women, and children.

　　5.检验

　　5. Inspection

　　(1)、检验标准：①按合同要求及有关规定、实物样品和GSBY76001—88《出口衬衫熨烫外观样照》。SN/T1932.7—2008《出口衬衫检验规程》。

　　(1) Inspection standards: ① According to the contract requirements and relevant regulations, physical samples and GSBY76001-88 "Appearance Sample of Export Shirt Ironing". SN/T1932.7-2008 "Inspection Regulations for Export Shirts".

　　(2)检验项目：

　　(2) Inspection items:

　　1、成衣外型测定，以目测为主，对照款式样(确认样)，按合同或标准及有关规定等查对实货是否依照规定生产，商标、吊牌、尺码带定位是否正确。

　　1. The measurement of the appearance of ready to wear clothing is mainly based on visual inspection, comparing with the style sample (confirmed sample), checking whether the actual goods are produced according to the contract or standards and relevant regulations, and whether the positioning of trademarks, tags, and size bands is correct.

　　2、熨烫定型，检验领子部位，立领衬衫，领圆大小适宜，领尖插片要足不折尖，折叠端正，前、后身及袖身平服，挺括、袖口齐，无亮光、水渍、烫黄等，成衣外观整洁。

　　2. Ironing and shaping, first inspect the collar area. For standing collar shirts, the collar circle size should be appropriate, and the collar tip insert should be sufficient without folding, folded neatly. The front, back, and sleeve bodies should be flat, straight, and the cuffs should be neat without any bright light, water stains, or yellowing. The finished garment should have a neat appearance.

　　3、外观疵点：面料无明显疵点，无色差，详细要求按SN/T1932.7—2008《出口衬衫检验规程》。

　　3. Appearance defects: The fabric has no obvious defects, no color difference, and detailed requirements are in accordance with SN/T1932.7-2008 "Inspection Regulations for Export Shirts".

　　4、缝制检验：各部位线路顺直，双明线宽窄一致，牢固、针距密度符合规程要求，缝修大小一致，缝合吃势均匀不起绺，无毛漏开线、止口倒吐，扣位正确，扣牢固，扣眼无毛疵，对条、对格、对花部位符合规定。

　　4. Sewing inspection: The lines of each part are straight, the width of the double visible thread is consistent, firm, the needle spacing density meets the requirements of the regulations, the sewing size is consistent, the sewing force is uniform without any grain, there is no missing thread or inverted mouth, the buckle position is correct, the buckle is firm, there are no defects in the buttonhole, and the strip, grid, and flower parts meet the regulations.

　　5、检测规格尺寸：可按合同或规程进行测量主要有五部位，领大、衫长、胸围、肩宽、袖长，规格尺寸准确。

　　5. Testing specifications and dimensions: The main five parts can be measured according to the contract or regulations, including collar size, shirt length, chest circumference, shoulder width, and sleeve length, with accurate specifications and dimensions.

　　(3)辅料：

　　(3) Accessories:

　　缝线与面料应一致，(顺色)面料缩水率要准确，纽扣大小一致，无残扣，水洗后效果优良，有柔软感，无黄斑，水渍等。

　　The stitching should be consistent with the fabric, the shrinkage rate of the (color) fabric should be accurate, the button size should be consistent, there should be no residual buttons, the effect after washing should be excellent, there should be a soft feeling, no yellow spots, water stains, etc.

　　检验操作程序：检验动作要统一，检验时应把衬衫衣领位置向上平放于检验台上，折叠衬衫检验折叠外观，然后按检验程序逐项进行检验，从上到下，先看左，后看右，看完表面，看里面，翻过来检验包缝线。应顺直无脱落现象。

　　Inspection procedure: The inspection action should be unified. During inspection, the collar of the shirt should be placed flat on the inspection table with the collar facing up. When folding the shirt, the folding appearance should be inspected first, and then the inspection should be carried out item by item according to the inspection procedure, from top to bottom, looking left first, then right, looking at the surface, looking inside, and finally flipping over to inspect the stitching. It should be straight without any detachment phenomenon.

　　(4)质量要求：

　　(4) Quality requirements:

　　外观：折叠端正，熨烫平挺，商标、尺码标位置端正准确，无歪斜。

　　Appearance: Foldable neatly, ironed flat and straight, the position of the trademark and size label is correct and accurate, without any tilt.

　　领子：领面平服，无外翻。松紧适宜，领圆大小要一致，领不起泡、渗胶，明线顺直，无跳线，接线，止口无反吐，领尖大小对称，领尖无断尖，领头圆顺，领豁口大小适宜。绱领子三点定位准确，不偏斜，底领不外露。

　　Collar: Flat collar with no outward rotation. The tightness should be appropriate, the size of the collar should be consistent, the collar should not have bubbles or glue leakage, the exposed wire should be straight, there should be no jumpers or wiring, the stopper should not be reversed, the collar tip size should be symmetrical, the collar tip should not be broken, the collar tip should be smooth, and the collar gap size should be appropriate. The three-point positioning of the collar is accurate, without deviation, and the bottom collar is not exposed.

　　门衿：门衿应平服，松紧适宜，宽窄一致，线路顺直，双明线宽窄一致，无接线、断线，销眼间距应均匀，无漏针、断线，开刀利落，无线毛，扣位与扣眼应相符，钉扣要牢固，扣大小一致，无残扣。门、里衿长短应一致。

　　Door frame: The door frame should be flat, with appropriate elasticity, consistent width, straight lines, and double exposed wires with consistent width. There should be no wiring or breakage, and the spacing between the pin holes should be even without missing or broken wires. The cutting should be sharp and free of burrs. The buckle position should match the buckle hole, and the nail buckle should be firm, with consistent buckle size and no residual buckles. The length of the door and lining should be consistent.

　　前身：过肩，线路顺直，松紧适宜，口袋位置端正，线路顺直，封口大小一致、牢固，底摆折边宽窄一致，线路顺直，圆底摆圆度一致。

　　Predecessor: Shoulder pass, straight line, suitable elasticity, pocket position upright, straight line, consistent and firm sealing size, consistent width of the bottom hem, straight line, and consistent roundness of the round bottom hem.

　　袖子：绱袖子，上袖缝与底袖缝相交处，袖底十字处应相对，袖开叉应顺直，长短；宽窄符合要求，袖叉中间扣位准确、袖头、应圆顺或方正，线路顺直，止口无反吐，眼与扣位相对称，两袖长短应一致，两袖口大小应一致，袖头圆顺，方正应一致。

　　Sleeve: Insert the sleeve, with the upper sleeve seam intersecting with the bottom sleeve seam, and the cross at the bottom of the sleeve facing each other. The sleeve slit should be straight and long; The width meets the requirements, the middle buckle of the sleeve fork is accurate, the sleeve head should be round, smooth or square, the line should be straight, the stopper should not be backfired, the eye and buckle positions should be symmetrical, the length of the two sleeves should be consistent, the size of the two cuffs should be consistent, the sleeve head should be round, smooth, and square.

　　后身：后领口无吃纵，过肩线路顺直，松紧适宜，底摆折边宽窄应一致，熨烫平服。

　　Rear body: The back neckline should not be too tight, the shoulder line should be straight, the elasticity should be appropriate, the width of the bottom hem should be consistent, and it should be ironed flat.

　　衫里：应把衬衫翻出里面，检验各部位包缝线应牢固，无脱落，缝头大小一致，洗涤成分标位置准确。

　　Inside the shirt: The shirt should be flipped out to check that the stitching on each part is firm, not loose, the size of the seams is consistent, and the position of the washing ingredient label is accurate.

　　检验结果判定按SN/T1932。7—2008《出口衬衫检验规程》

　　The inspection results are judged according to SN/T1932. 7-2008 Inspection Regulations for Export Shirts

　　本文由 济南工作服  友情奉献.更多有关的知识请点击  http://www.ymsfs.com/   真诚的态度.为您提供为的服务.更多有关的知识我们将会陆续向大家奉献.敬请期待.

　　This article is a friendly contribution from Jinan workwear For more related knowledge, please click http://www.ymsfs.com/ Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.